Quality Inspection Digital Marketing
Resume:
Karen T. Hewitt
Eastlake OH 44095
**************@*****.***
WORK EXPERIENCE
Morrison Products-Cleveland OH-March 2024 to May 2024 Quality Auditor-inspected various sized blower wheels for air systems and components for the wheels and housings made on various punch presses. I used indicators, calipers, no go gages, pin micrometers, height stand, blade angle, blade count and radius gages, vision check machine to verify wheel that prints out label for my inspection sheet by each audit line, an automatic torque rig (wheel hub torque) and computer connected to a hub bore to check frequency of wheel, all recorded on inspection sheets. I also checked each wheel balancer’s (180-degree variance check) paperwork each audit (every 2 hours) to ensure wheels are properly balanced (variance numbers are in range) after being assembled by press operator; also, a label from each balance machine (2) is placed on their paperwork. At the end of the shift, I recorded scrap from doing hub torques, number of inspections, balances and set-ups on all the punch presses and balancers. (very hot and noisy environment) Staffworks-Willoughby OH- October 2023 to February 2024 Cell Technician- temp at Parker Gas Turbine Fuell Systems Division in Mentor OH; I worked primarily in quality, ran a Zeiss CMM using the Calypso program on various marine, auto and aerospace parts for various customers including military/government contracts; checked finishes using a profilometer; then moved orders to next operation; used Solumina software program to enter CMM and order data for the next operation or to print out reports, depending on type of traveler; helped out when not busy in the macro spray cell during various duties like od gaging, buffing parts, putting them through rinse cycles, painting screws, etc. (temporary job no open positions) Heeter Printing- Eastlake OH- July 2023 to September 2023 Mailroom Helper- at a provider of complex print, direct mail, fulfillment and digital marketing to several industries such a medical and education; I performed various duties such as stuffing, sealing, stamping, addressing and video printing envelopes, ran a Flowmaster machine which folds and puts inserts into envelopes and seals them; sorted letters from the conveyor belt into bins for mail prep; also ran a tabletop machine that folds the inserts and puts into envelopes and an envelope sealers; tagged bins to put on skids, used a pallet jack to move skids and any help needed to process various orders. (seasonal work not fulltime)
Karen T. Hewitt
34800 Vine Street Apt 201 E
Eastlake OH 44095
**************@*****.***
WORK EXPERIENCE (cont’d)
Slabe Machine Products- Willoughby OH- November 2022 to May 2023 In-process inspector- at a manufacturer of small, complex aerospace parts including military and government contracts, performed floor inspection (to check for visual defects or discrepancies) for machines such as CNC, Milling, Swiss, Water Jet, Multi-Spindles and grinders; ran the Zeiss CMM (uses Calypso program) frequently to check parts with programs (for operators and/or for my own inspection), printed out documents for machinists such as visual dimension documents; supported process improvement with machinists and supervisors; checked yellow tags, to move finished trays onto the next operation such a different machine or outside processes; used various hand gages (calipers, micrometers, pin gages), comparators, smart scope, Keyence, concentricity gage, height stand, depth gage, indicators, profilometer, made molds for id checks; counted inventory Meritec- Painesville OH- January 2022 to August 2022 Quality Inspector- (temp until May through Hartman Personnel before hired in) I started in electronic assembly; trimming and cutting cables and various components involving high performance electrical and electronic interconnect systems and connectors using visual and handiwork skills, such as using a soldering stick, metal hand clippers and pneumatic machinery; worked primarily in quality (mold department); did hourly floor checks and first pieces (recording measurements on inspection sheets) on components molded from machines (such as a Cincinnati Milacron and Arburg Mold); used calipers, microscopes, pin gages, micrometers and a pull tester; visually checked boxes of completed mold parts; worked in the PSI (pre-shipping inspection) area, inspecting completed products such as cables and various electronic components before shipping, using tape measure/ruler, UV light to verify product was tested and wrote up a certificate of conformance and updated records on pc. Read blueprints, verified part counts using scale, created labels with info for the customer or in-house production use; got trained on NCR procedures and good documentation practices; had an email for communication in-house; inspected and assembled parts used in medical such as for MRI machines; assisted mold operators, leads and the supervisor on my shift (2nd).
The last month I was in a separate building which makes only cable harnesses for one customer; did in- process hourly inspections of all processes such as wire making, lay-outs and welding, filling out paperwork; used microscopes, video monitors, tweezers and calipers; verified pull tests and paperwork done correctly, checked for operator issues, ensuring work was being produced to customer specifications; also checked completed cable harnesses pre-welding Karen T. Hewitt
34800 Vine Street Apt 201 E
Eastlake OH 44095
**************@*****.***
WORK EXPERIENCE (cont’d)
Career Centered Staffing- Eastlake OH- August 2019 to October 2019 Quality Control Lab Tech-temp at Paulo Cleveland (heat treating and brazing)in Willoughby OH- I verified cycle, process, calibration and parts; prepared data, graphs, orders, certs for customers; notified production, quality manager or Braze/Production, of non-conforming product, checked loads in- process; reviewed/marked furnace charts for compliance; prepared certs for shipping; hardness checks with Rockwell machines; order writing, emailed customers for chart approval or order issues; prepped braze samples, did SATs (survey accuracy test)to check furnace is reading at proper temperature; used Microsoft Word, Excel, Outlook and special programs created by Paulo; laid off Norman Noble, Inc.- Highland Heights OH – August 2018 to May 2019 Quality Inspector-ran a Smartscope to inspect tiny medical components, did first piece and final inspections (various sized medical screws, components of internal medical devices, etc.) using visual, microscope, micrometers, calipers, pin gages, comparators, MicroVu, profilometer, height stand and weight scale to verify counts on very tiny parts (titanium, stainless steel, various alloys materials used) Star Precision Technologies- Mentor OH – October 2017 to July 2018 Quality Inspector II-did incoming, first piece, in-process and final inspections on metal components
(brass, plastic materials, alloy, stainless steel, aluminum, etc.) manufactured in-house, by another customers, vendors, or their sister company Alloy Bellows & Precision Welding; used a CMM, calipers, mics, molds for id checks, comparator, bore gages, indicators, depth micrometers, pin gages, Rockwell machinery for hardness testing; emailed customers or internally when orders were ready to be shipped or for issues; did PPAPs, used E2, Microsoft Word, Excel, Outlook; laid off (Alloy/Star are now in one building called Alloy Precision Technologies in Mentor OH) Alloy Bellows & Precision Welding- Highland Heights OH – Feb 2016 to Oct 2017 Quality Inspector-I did incoming, first piece, in-process, final inspections and reports on sister company Star’s parts used to assemble Alloy’s various products, in-house production (bellows, welding, components for hydraulic and electrical, etc.), used mics, calipers, pin gages, comparator, etc. along with a hand-held x-ray gun to verify material to be used for production and incoming inspections; did PPAPs when needed; helped at Star Precision where I was transferred Karen T. Hewitt
34800 Vine Street Apt 201 E
Eastlake OH 44095
**************@*****.***
WORK EXPERIENCE (cont’d)
USM Precision Products Inc. – Willoughby OH – July 2012 to Sept 2015 Quality Inspector-learned some GD&T and blueprint reading, how to use hand gages, basic inspection equipment and how to be a quality inspector; ran 2nd shift solo doing first piece inspections, SPC checks and random floor checks using comparators, height stand, profilometer, pin gages, various mics/calipers, CMM etc.; did audits, calibrations, PPAPs, used a program called OASIS that checked SPCs; Acme machines, hydromats, CNCs, Milling, etc.; I checked; they used stainless steel, brass, alloy, titanium, aluminum and other various materials; used Excel and Word to create the quality documents, such as PPAPS, I assisted operators and supervisor; industries were plumbing, electrical, automotive, nuclear, etc.; laid off; now out of business
EDUCATION
Lakeland Community College, Kirtland OH, between March 1998 -June 2003 I took courses for Electronic Engineering (25.7 credit hours completed) which included Applied Physics I, Tech Math I, English I to III, Computer Science and Social Science; not completed Willoughby-Eastlake Technical Center, Willoughby OH, August 1992 - June 1994; obtained a vocational certificate in June 1994 in the Financial Specialist program; courses included accounting, typing, English, office skills and general courses (needed for diploma) North High School, Eastlake OH, August 1990 - June 1992 (honor courses); June 1994 diploma CERTIFICATIONS
*” Building An Environment of Trust Training” from Lakeland College, 4 hr course via USE (Feb 2010)
*” No Sweat Blueprint Reading” from Excel Training, Inc. via USM (October 2012)
*Heartsaver First Aid CPR AED Card from AHA (safety team member at US Endoscopy, USM and AB) Karen T. Hewitt
34800 Vine Street Apt 201 E
Eastlake OH 44095
**************@*****.***
REFERENCES
Dan Jansen (former quality manager at USM Precision Products) Jade Products Inc. (quality supervisor)
9309 Mercantile Drive
Mentor OH 44060
Bruce Herrick (recruiter for Meritec)
Hartman Personnel
8789 Tyler Blvd
Mentor OH 44060
Joseph Bush (former 2nd shift supervisor)
Meritec
1382 W Jackson Street
Painesville OH 44077
Contact this candidate